C.R. Laurence Co., Inc.
Sign OnSign Off  |  Your Account  |  View Cart  |  Help  |  Home


View Larger Image

Catalog Number: 71016U1
Finish: ALUMINUM


  • Superior Weather Resistance

  • 100% Solids Content

  • Available in Aluminum and Black Colors


  • CRL Tremco® 440 Butyl Architectural Tape is a pre-formed butyl sealant in tape form. The 100 percent solids compound of butyl and polyisobutylene contains no solvents or other volatiles that could escape on exposure, causing shrinkage and sealant failure. Tremco® 440 forms a watertight seal to prevent water infiltration, and has superior weather resistance. Highly adhesive, it remains permanently elastic, even at low temperatures, and is adaptable to many different types of glazing systems. Use Tremco® 440 for non-compression glazing of vision lites and spandrel panels in metal and wood frames in low rise building construction. It can also be used for lap sealing between panels such as steel, aluminum and porcelain, as well as a variety of other joints in shear between similar and dissimilar materials.



    CRL Aluminum 1/8" x 3/8" Tremco® 440 Butyl Architectural Tape


     


    Other Products/Finishes/Sizes:

    CATALOG NUMBER DESCRIPTION COLOR
    71009F1 CRL Aluminum 1/16" x 1/4" Tremco® 440 Butyl Architectural Tape
    710CAH5 CRL Black/Bronze 1/16" x 1/4" Tremco® 440 Butyl Architectural Tape
    71049N1 CRL Aluminum 1/16" x 3/8" Tremco® 440 Butyl Architectural Tape
    71049Q1 CRL Black/Bronze 1/16" x 3/8" Tremco® 440 Butyl Architectural Tape
    71010W1 CRL Aluminum 1/16" x 1/2" Tremco® 440 Butyl Architectural Tape
    71010B1 CRL Black/Bronze 1/16" x 1/2" Tremco® 440 Butyl Architectural Tape
    71016U1 CRL Aluminum 1/8" x 3/8" Tremco® 440 Butyl Architectural Tape
    71016W1 CRL Black/Bronze 1/8" x 3/8" Tremco® 440 Butyl Architectural Tape
    71017F1 CRL Aluminum 1/8" x 1/2" Tremco® 440 Butyl Architectural Tape
    71017H1 CRL Black/Bronze 1/8" x 1/2" Tremco® 440 Butyl Architectural Tape
    71024R1 CRL Aluminum 3/16" x 1/2" Tremco® 440 Butyl Architectural Tape
    71024G1 CRL Black/Bronze 3/16" x 1/2" Tremco® 440 Butyl Architectural Tape
    71029G1 CRL Aluminum 1/4" x 1/2" Tremco® 440 Butyl Architectural Tape
    71029D1 CRL Black/Bronze 1/4" x 1/2" Tremco® 440 Butyl Architectural Tape

    Catalog Number:71016U1
    Also Available in These Catalogs:
    CRL03 Sealants, Adhesives, and Fasteners, PAGE N170
    CRL93G Sealants and Fasteners, PAGE SF054
    Color:Aluminum
    Thickness:1/8" (3 mm)
    Width of Tape:3/8" (10 mm)
    Roll Length:25' (7.6 m)
    Ship Via:Can Ship UPS
    Shipping Weight:1.5 lb (680g)
    Case Qty:20

    Typical Properties
    Base Polymer: cross-linked butyl rubber (polyisobutylene); Solids Content: 100% by weight; Cure Time: fully cured before application; Hardness: 65 durometer Shore "00"; Temperature Range: Application 20°F (-7°C) to 120°F (49°); Service -40°F (-40°C) to 158°F (70°C); Weathering: Unaffected by ultra violet through glass. Remains flexible at low temperatures.

    Limitations: Not for use in joints subjected to continuous water immersion or temperatures exceeding 158°F (70°C). Not for use with lites of glass over 75" (1.91 m). As the size of the lite approaches this maximum a higher performance glazing system, such as CRL Tremco® Pre-Shimmed Butyl Tape should be considered.

    Applicable Standards: AAMA 800-92, 804.3, and 807.3.

    Good Glazing Practices: The following "Good Glazing Practices" are recommended when using CRL Glazing Tapes. Surfaces to be adhered should be free of frost or standing water, brushed clean, solvent washed (MEK, Toluene or Naptha) and wiped dry. At installation, positive contact and approximately 10 percent compression is recommended to fully marry surfaces to be joined. Glazing tapes kept under compression with clips or wedges provide the best seals.

    Always use setting blocks (80 durometer Shore "A" hardness) placed at the sill quarter points. Spacing shims are recommended to accommodate wind loading when glass lite is over 100" (50 durometer Shore "A" hardness). Tape placement on the sill rabbet is not to be below the sight line unless a cap bead is specified, then tape is placed 3/16" (4.76 mm) below the sight line to allow for the cap bead. Do not overlap tape to join; always butt ends without stretching. To keep tape surface clean, leave release paper in place until ready-to-set the glass.

    Limitations: Not for use in joints subjected to continuous water immersion or temperatures exceeding 158°F (70°C). Not for use with lites of glass over 75" (1.91 m). As the size of the lite approaches this maximum a higher performance glazing system, such as CRL Tremco® Pre-Shimmed Butyl Tape should be considered.

    Most shipping weights are approximate and have not been verified. If the exact weight is needed in order to determine shipping costs, and shipping costs are required in order for you to complete your order, please request this prior to submitting your order by contacting CRL Customer Service. Product images shown are of the actual product or a close representation. ColorsColours can vary depending on your computer's video card and on how your monitor's colorcolour is adjusted.