C.R. Laurence Co., Inc.
Sign OnSign Off  |  Your Account  |  View Cart  |  Help  |  Home

View Larger Image

Catalog Number: TSK50

  • Machine Use VE4, VE4PLUS1, VFE4C, VFE6C
  • Two to Three Fold Increase in Diamond Wheel Life
  • Available for Purchase or Lease
  • Eliminates Tank Dig-Out
  • Specially Designed Tank with Sweep System
  • Reduce or Eliminate Disposal Costs
  • Improved and Consistent Finished Product
  • UL Certified Control Panel, NEMA 12 Enclosures

  • Longer Diamond Wheel Life and Quality Glass Finishing! This is a fully assembled, turn-key Coolant Filtration System ready-to-install and go to work. The system is designed for continuous separation of glass fines from coolant. It incorporates the latest design features to sweep the tank bottom and isolate clean fluid. Two basic systems are offered.

    CRL Coolant Filtration for Edgers and Bevellers


    Other Products/Finishes/Sizes:

    TSK50 CRL Coolant Filtration for Edgers and Bevellers

    Catalog Number:TSK50
    Also Available in These Catalogs:
    Height:42" (1.07 m)
    Filter Capacity:430 Ci (7.6 ltr)
    Coolant Tank Capacity:150 Gallons (568 ltr)
    F.O.B :Cicero, Il.
    Shipping Weight:1805 lb (818.73kg)

    Installing a Filtration System for your beveling or edging operation will assure the removal of glass fines from the coolant. As the glass fine laden liquid discharges from the machine, it travels into the centrifuge. The tank design has built-in water jet nozzles so the liquid is consistently agitated and not allowed to settle. The glass fines are kept in suspension until they reach the rotor bowl. Once the dirty liquid reaches the rotor bowl, it is spun at very high speeds which causes the glass fines to separate from the coolant, and the solids are collected in the bowl. The operator removes the bowl which is filled with glass sludge and disposes the waste, then returns the bowl and turns the system back on.

    How to Select the Filtration System That Will Work Best for You - Our Coolant Filtration System models are matched with machinery based on total grinds produced and flow rate. The flow rate is the amount of coolant being pumped through the machine's coolant system. Each filtration centrifuge has a rotor volume that dictates the model to use with the machine. Too small a unit would mean the rotor bowl would fill-up with sludge too fast and have to be emptied too often. The main objective in filter sizing is not having to empty the rotor every hour. The ideal cleaning frequency would be once or twice a day or eight hour shift. These Coolant Filtration Systems can be run overnight without the machinery to achieve optimum cleaning. Centralized systems can be designed for any fabrication operation. See the chart below for typical machine reference and general recommendations.

    Controls: All controls are built to OSHA requirements, utilizing CE, CSA and UL Certified components. Wiring for three phase, 60 cycle, 230V AC power.

    Electrical - TSK50: Three Motors, Total 4.25 HP (3.2 kw) and TSK80: Three Motors, Total 5.25 HP (3.9 kw)
    Voltage - Both Models: Three Phase, 60 Cycle, 230V AC
    Power - TSK50: 20 AMP @ 230V AC and TSK80: 30 AMP @ 230V AC

    Converters are available to operate the TSK50 or TSK80 at Single Phase, 60 Cycle, 220V AC.

    Height: 42" (1.07 m)
    Footprint: 48" x 72" (1.22 x 1.83 m)
    Shipping Weight: CAT. NO. TSK50: 1805 lbs. (818 kg) and CAT. NO. TSK80: 1965 lbs. (891 kg)
    Coolant Tank Capacity: 150 Gallons (568 ltr)

    Most shipping weights are approximate and have not been verified. If the exact weight is needed in order to determine shipping costs, and shipping costs are required in order for you to complete your order, please request this prior to submitting your order by contacting CRL Customer Service. Product images shown are of the actual product or a close representation. ColorsColours can vary depending on your computer's video card and on how your monitor's colorcolour is adjusted.